applications

DIN-AP3

The Crestron® DIN-AP3 is a 3-Series Control System® designed for DIN rail mounting applications. Featuring the 3-Series® control engine, the DIN-AP3 forms the core of any modern networked home or commercial building, managing and integrating all the disparate technologies throughout the facility to make life easier, greener, more productive, and more enjoyable.

Control Engine
  Crestron 3-Series; real-time, preemptive multi-threaded/multitasking kernel; Transaction-Safe Extended FAT file system; supports up to 10 simultaneously running programs
Memory
  DDR3 SDRAM 256 MB
  Flash 4 GB
  Memory Card supports SD and SDHC cards up to 32 GB
Communications
  Ethernet 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer Protocol), FIPS 140-2 compliant encryption, IEEE 802.1X, SNMP, BACnet/IP [2], IPv4 or IPv6, Active Directory authentication, IIS v.6.0 Web Server, SMTP e-mail client
  Cresnet Cresnet master mode
  USB Supports computer console via front panel USB 2.0 device port
  RS-232/422/485 For 2-way device control and monitoring, supports RS-232, RS-422, or RS-485 up to 115.2k baud with hardware and software handshaking
  IR/Serial Supports 1-way device control via infrared up to 1.2 MHz or serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
Connectors & Card Slots
  I/O 1 – 8 (1) 9-pin 3.5 mm detachable terminal block;
Comprises (8) “Versiport” digital input/output or analog input ports (referenced to GND);
Digital Input: Rated for 0-24 Volts DC, input impedance 20k Ohms, logic threshold >3.125V low/0 and <1.875V high/1;
Digital Output: 250 mA sink from maximum 24 Volts DC, catch diodes for use with “real world” loads;
Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC maximum, input impedance 21k Ohms with pull-up resistor disabled;
Programmable 5 Volts, 2k Ohms pull-up resistor per pin
  Ground (1) Captive screw terminal;
Chassis ground lug
  MEMORY (1) SD memory card slot;
Accepts one SD or SDHC card up to 32 GB for memory expansion
  RELAYS 1 – 4 (1) 8-pin 3.5 mm detachable terminal block;
Comprises (4) normally open, isolated relays;
Rated 1 Amp, 30 Volts AC/DC;
MOV arc suppression across contacts
  COMPUTER (1) USB Type B female;
USB 2.0 computer console port (6 ft cable included);
For setup only
  NET (2) 4-pin 3.5 mm detachable terminal blocks, paralleled;
Cresnet master port and 24 Volt DC power input
  COM 1 – 2 (2) 5-pin 3.5 mm detachable terminal blocks;
Bidirectional RS-232/422/485 ports;
Up to 115.2k baud; hardware and software handshaking support
  IR/SERIAL 1 – 4 (1) 8-pin 3.5 mm detachable terminal block;
Comprises (4) IR/Serial output ports;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud
  LAN (1) 8-pin RJ45 jack;
10Base-T/100Base-TX Ethernet port
Controls & Indicators
  PWR (1) Dual-color green/amber LED, indicates operating power supplied from Cresnet network or power supply, turns amber while booting and green when operating
  NET (1) Amber LED, indicates communication with the Cresnet system
  MSG (1) Red LED, indicates processor has generated an error message
  HW-R (1) Recessed miniature pushbutton for hardware reset
  SW-R (1) Recessed miniature pushbutton for software reset
  LAN (2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity
Power
  Cresnet Power Usage 8 Watts (0.33 Amp @ 24 Volts DC)
Environmental
  Temperature 32° to 104° F (0° to 40° C)
  Humidity 10% to 90% RH (non-condensing)
  Heat Dissipation 26 BTU/hr
Enclosure
  Light gray polycarbonate housing with polycarbonate label overlay, UL94 V-0 rated, 35 mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45 mm front panel cutout, occupies 9 DIN module spaces (162 mm)
Dimensions
  Height 3.72 in (95 mm)
  Width 6.28 in (160 mm)
  Depth 2.29 in (59 mm)
Weight
  9.8 oz (277 g)